Skip to content
Request a Quote
Menu
Placeholder for a photo (BH-A13-S01-I01)

How to Choose a Plastic for Molded and Cast Parts

Choose a plastic by starting from what the part must do, not from a material you have used before.

List the loads, temperatures, chemicals, outdoor exposure and any flame or contact requirements, then shortlist the resin families that can meet them. Appearance, process and cost narrow the list from there. A material name can hide large differences. Polycarbonate covers many grades with different additives and properties, and a vacuum cast PC-like resin is a different material again. A usable specification names the grade, the color and any evidence you need. The guidance below is general. Confirm the material for your part with your supplier and, where a requirement is critical, by testing.

Requirements

Start with the conditions the part has to survive, because they rule out more materials than any other factor.

Start with What the Part Must Withstand

Write down the conditions the part will meet in use before you compare materials. Each one removes some resin families from the shortlist, and one or two often decide the choice.

Load and stiffness

Whether the part carries a steady load, flexes repeatedly, takes impacts or holds a snap fit. Plastics creep under sustained load, so a constant load needs a different review from occasional knocks.

Temperature

The highest and lowest temperatures in use, how long the part stays there and whether it is loaded at the same time. Stiffness falls as temperature rises, and some plastics become brittle in the cold.

Chemicals and cleaning

Oils, fuels, solvents, cleaning agents or disinfectants the part will touch. Some plastics, transparent ones in particular, can crack when under stress and exposed to certain chemicals.

Outdoor exposure

Sunlight, weather and moisture. Many plastics fade, chalk or become brittle under UV light unless the grade is stabilized or the surface is protected.

Flame and contact requirements

Any flammability rating, food contact, skin contact or electrical requirement the product must meet. These belong to a specific grade and its documentation, not to a resin family.

Rank the requirements. Mark the ones the part must not fail and the ones where a compromise is acceptable, so a supplier knows which to protect.

Placeholder for a diagram (BH-A13-S02-I01)

Resin Families

With the requirements ranked, the common resin families can be compared against them.

Compare Common Resin Families

The table gives the typical strengths of some common families in general terms. Grades within a family vary widely, especially with fillers or additives, so use it to build a shortlist, then check the data sheets of the actual grades.

Resin familyTypically chosen forCheck before choosing
ABSHousings and covers that need a balance of toughness, appearance and ease of moldingStandard grades have limited heat and UV resistance, and some solvents attack it
PC (polycarbonate)Impact strength and transparency; also blended with ABS for tougher housingsCan crack under stress with some chemicals, and the surface scratches without a hard coat
PP (polypropylene)Chemical resistance, low weight and living hinges in caps and containersLower stiffness, some grades turn brittle in the cold, and it is hard to bond or paint
PA (nylon)Toughness and wear resistance; glass-filled grades add stiffness for structural partsAbsorbs moisture, which changes its dimensions and properties
POM (acetal)Low friction, stiffness and dimensional stability in gears, clips and moving partsHard to bond or decorate, and standard grades need UV protection outdoors

Other families cover other needs, for example PMMA (acrylic) for clarity, thermoplastic elastomers for soft-touch areas and seals, and PEEK or PPS for high temperatures. In every family, the grade sets the properties, not the family name.

Appearance

Function narrows the list. Appearance often decides between the materials that remain.

Define Appearance, Color and Texture

Appearance can narrow the choice as much as function. Transparency, color, gloss, texture and feel are each easier in some materials than others, so state them before the material is fixed.

Transparency

A clear part limits the choice to transparent grades, such as PC, PMMA or clear grades of other families. Clarity also depends on wall thickness and the mold or master surface.

Color

Specify color against a physical sample or a named color reference. Color can come from pre-colored material, a masterbatch added at molding or a later coating, and each gives a different result. Some resins are naturally off-white or yellowish, which can limit pale or bright colors.

Texture and gloss

A molded texture comes from the mold surface, so it is specified with the tool. The same texture can look different on different resins, and deeper textures usually need more draft to release cleanly.

Feel

A soft-touch surface can come from a soft material such as a thermoplastic elastomer, from overmolding a soft layer onto a rigid part or from a coating. State whether the target is the feel, flexibility or a measured hardness.

Keep cosmetic and functional requirements in one specification, because a pigment, filler or coating can change the properties you chose the material for.

Placeholder for a photo (BH-A13-S04-I01)

Cast Resins

If the first parts will be vacuum cast, the material question changes, because cast parts are not made from the production plastic.

Cast Resins Versus Production Plastics

Vacuum cast parts are made from two-part casting resins, commonly polyurethanes, chosen to simulate selected properties of a production plastic. Suppliers describe them as ABS-like, PP-like, PC-like or rubber-like. The description names a comparison, not the material: an ABS-like cast part is not ABS.

Cast resins can come close in appearance, stiffness or hardness, which makes them useful for looks, fit and handling. They usually differ in grade-dependent properties such as heat and chemical resistance, flammability and long-term load behavior.

What cast parts can show

Form, fit, appearance, color and general handling, and early user feedback on a design that may still change.

What usually needs the production plastic

Tests or approvals that depend on the grade, such as temperature, chemical exposure, flammability, food or skin contact, outdoor aging and long-term load.

How to specify the cast resin

Name the production plastic the parts should represent and the properties that matter most, then ask for the actual casting resin and its data sheet.

Placeholder for a photo (BH-A13-S05-I01)

Specification

Whichever process makes the parts, the material choice only holds if it is written where the supplier will read it.

Specify the Material on the Drawing

A family name such as nylon or PC leaves too much open. Write the material in the drawing's material block or notes, or in the purchase specification, with enough detail that two suppliers would buy the same thing.

  • The family and grade, with the material producer if a specific grade is required.
  • Any filler, reinforcement or additive, such as glass fiber, UV stabilizer or flame retardant.
  • The color, by reference sample or color code, and whether it comes from pre-colored material or a masterbatch.
  • Whether regrind may be used.
  • Whether an equivalent grade is acceptable, and who approves a substitute.
  • Any certificate or record required, such as a material certificate, flammability documentation for the grade, or food-contact or RoHS-related declarations.

For cast parts, also name the production plastic the resin should represent and the properties it must match, so the cast parts are judged against a stated purpose.

Placeholder for a diagram (BH-A13-S06-I01)

Testing

A data sheet narrows the choice, but its values are measured on standard test pieces, not on your part.

Test Before You Commit

A data sheet reports properties measured on standard specimens under stated conditions. Your part has its own geometry, wall thickness, gate positions, weld lines and service conditions, so the data sheet supports the choice but does not prove it.

Plan a test when a requirement is critical and the margin is unclear, for example when:

  • The part carries a load for long periods or at temperature.
  • It meets chemicals, cleaning agents or outdoor exposure.
  • A flammability, contact or electrical requirement applies to the finished product.
  • Snap fits, living hinges or thin sections must survive repeated use.
  • You are changing to a new grade, color or material supplier.

Cast or machined parts can support early checks, but a result that depends on the grade generally needs molded parts made under the intended process. Bohui produces vacuum cast and injection molded parts in its own factory, so you can discuss early cast parts and molded test parts in one enquiry.

Discuss the Requirement with Bohui

Share the part information and the decision you need to make.

Placeholder for a contact photo of Jane

Jane

BOHUI PROTOTYPES LIMITED

I'm Jane, the contact for your enquiry.

You can also reach me by email or on WhatsApp.

Jane

BOHUI PROTOTYPES LIMITED

  • Address: Xiaobian Street, Chang'an Town, Dongguan City, Guangdong Province, China

Request a Quote

Fields marked  are required.

Jane BOHUI PROTOTYPES LIMITED Privacy Policy