Skip to content
Request a Quote
Menu
Placeholder for a photo (BH-P032-S01-I01)

Injection Mold Making for Custom Plastic Parts

An injection mold is built for one part design, and it decides how that part fills, cools and releases for as long as the tool runs.

Specify the mold from three things: the part it has to make, the quantity you expect and the tool life your project needs. Then review the design before tool making starts. Bohui produces injection molded parts in its own factory and offers mold development together with molding, so the tool and the parts it makes can be discussed as one project.

Mold Requirements

Start with what the mold must deliver, because every later choice about the tool follows from it.

What the Mold Has to Deliver

A mold quotation describes a tool, but what you are buying is a supply of parts. Define that supply first, and the tool can be specified to match it.

The part

Its geometry, resin and color, critical dimensions and cosmetic faces, which the mold must reproduce on every shot.

The quantity

The first order, expected annual demand and how long the part stays in production. These decide how many cavities make sense and how much the tool is worth.

The tool life

How many parts the mold must make over the project, and how long it must stay usable between orders. A short validation run and years of production call for different tools.

Abrasive resins, such as glass-filled grades, wear a mold faster, and tight tolerances or textures tolerate less wear, so state them with the tool life.

Placeholder for a photo (BH-P032-S02-I01)

Tool Specification

With the part, quantity and tool life defined, the tool itself can be specified.

Specify the Tool

Most of a mold's cost and performance comes from five choices. Ask for each to be stated in the quotation, so that different quotations describe the same tool.

Cavities

A single-cavity mold makes one part per cycle; a multi-cavity mold makes several, at a higher tool cost and a lower part cost. A family mold makes different parts together, but they may not fill evenly.

Gate and runner

The gate is where plastic enters the part. A cold runner solidifies with the part and is separated as scrap or regrind; a hot runner keeps the plastic molten up to the gate and wastes less, at a higher tool cost.

Ejection

Ejector pins, sleeves or plates push the part out of the mold and leave small marks. Agree where they may sit, away from cosmetic faces.

Side actions

Slides and lifters release undercuts such as side holes and snap hooks. Each one adds tool cost and maintenance, so ask which features need one.

Tool material

Hardened tool steel is the usual choice for long runs and abrasive resins. Softer steels and aluminum are easier to machine and change, and are often used for shorter runs. Ask which material is proposed and why.

Cooling and venting belong in the proposal too, since they affect cycle time, warp and surface quality.

Placeholder for a diagram (BH-P032-S03-I01)

Design Review

These choices should be settled against a reviewed part design, before tool making starts.

Review the Part Design Before Tool Making

A design for manufacturing (DFM) review checks the part against the way the mold will be built and run. Ask for it before the mold design is released, while its findings are still edits to the model rather than changes to the tool.

Expect specific findings that you can accept or reject:

  • Walls, ribs and bosses that may cause sink, warp or voids.
  • Faces that need more draft, including textured faces.
  • Undercuts and the side actions or design changes that release them.
  • Proposed gate, parting line and ejector positions against your cosmetic faces.
  • Critical dimensions to leave steel-safe, so a correction removes metal from the mold rather than adding it.

Some projects add a mold flow simulation to predict filling and warp. Record accepted changes in a new model revision, and release the mold design only from that revision.

Trials and Approval

A reviewed design gives the first trial a fixed reference to be measured against.

Trials, Samples and Mold Approval

The first parts from a new mold are trial samples, molded while the process is still being set. They show whether the tool fills, ejects and holds the drawing, and what still needs to change. Agree before tool making how trials are reviewed and how approval is recorded.

Trial rounds

Labels such as T0 and T1 are not standardized. Define what each round must show, how many samples come with it and which records you need.

Sample review

Check molding defects, critical dimensions, appearance and fit separately, against the drawing revision and an agreed appearance reference.

Corrections

Record each issue and whether it needs a process adjustment, a tool correction or a design change, since responsibility and cost are usually agreed differently for each.

Approval

Approve a named sample, its inspection report and the process conditions used to make it, so that production runs from the same basis.

Placeholder for a photo (BH-P032-S05-I01)

Changes and Storage

Once the mold is approved, it still has to be maintained, kept safe between orders and sometimes changed.

Plan Changes, Maintenance and Storage

A mold wears with use and may outlast several design revisions. Agree how it will be changed, maintained and kept when the tool is ordered, not when a problem arises.

Design changes

Removing steel from the mold, for example to make a feature larger on the part, is usually simpler than adding it, which may need welding or a new insert. A change can need a new sample review before production resumes.

Maintenance

Molds need routine cleaning and inspection, and components such as ejector pins, slides, gates and vents wear with use. Ask how maintenance is planned and recorded, and how repairs are authorized.

Storage

Between orders, a mold should be cleaned, protected against corrosion, identified and kept in a secure place.

Agree these points in the order:

  • Who owns the mold and its design data.
  • Where the mold is stored and how it is identified.
  • How maintenance, repairs and replacement are authorized and paid for.
  • What happens if the mold is inactive for a long period.
  • The conditions for moving the mold to another site or supplier.

Prototype vs Production

How much to invest in the tool depends on whether the project needs a prototype or a production mold.

Prototype Molds and Production Molds

Not every project needs a production mold at the start. A prototype mold, sometimes called a bridge tool, makes parts in the production resin from a simpler, less durable tool, so the design can be tested in the real material before the full investment.

Prototype molds

Often single-cavity, in aluminum or a softer steel, with simpler cooling and hand-loaded inserts in place of some slides. They suit design validation, pilot builds and smaller quantities, and they are easier to change.

Production molds

Built for the expected volume and tool life, typically in hardened steel, with more cavities where the quantity justifies them, mechanical side actions and cooling designed for a stable cycle. They cost more and take longer to make.

Choose by quantity, design stability, resin and timeline. A prototype mold suits a design that may still change; for a frozen design with a clear volume, going straight to a production mold avoids paying for two tools.

Placeholder for a diagram (BH-P032-S07-I01)

Questions

A few practical questions come up on most mold projects.

Mold Making Questions

Who owns the mold?

Ownership is agreed in the order, not assumed. Settle it together with storage, maintenance and repairs, and what happens if production moves or ends.

Should the mold be steel or aluminum?

It depends on the quantity, tool life, resin and how settled the design is. Hardened steel suits long runs and abrasive resins, while aluminum is mainly used for prototype and shorter-run tools.

How many cavities does my mold need?

Enough to meet your expected demand at a practical cycle. More cavities raise the tool cost and lower the part cost, but each cavity has to be filled, measured and maintained. Share your quantity plan to compare the options.

What do I need to send for a mold quote?

The 3D model and drawing, the resin and color, the first order and expected annual demand, cosmetic faces, critical dimensions and your sample milestone, where you know them. Then Request a Mold Quote.

Discuss Your Mold and Injection Molding Project

Tell me what the part needs to do, whether you need a new mold or have an existing tool, and the quantities you are considering.

Placeholder for a contact photo of Jane

Jane

BOHUI PROTOTYPES LIMITED

Include the model or drawing revision, intended resin and color, critical dimensions, visible surfaces, sample milestone and delivery destination where known. If a requirement is still open, say so in your message.

Prefer to contact me directly? Reach me by email or WhatsApp. You can describe the project first and discuss an appropriate way to share detailed files.

Jane

BOHUI PROTOTYPES LIMITED

  • Address: Xiaobian Street, Chang'an Town, Dongguan City, Guangdong Province, China

Request a Quote

Fields marked  are required.

Jane BOHUI PROTOTYPES LIMITED Privacy Policy