Injection Molding Design Guide
Design a molded plastic part around four decisions: walls close to one nominal thickness, draft on the faces that slide against the mold, undercuts only where a feature needs them, and a gate and parting line planned around the part's function and visible surfaces.
Each is easier to change in the model than in the mold. Once the tool is made, adding draft or moving a parting line can mean tool rework, another trial and a new sample review. The guidance below gives general starting points. The right values depend on the resin, the part and the tool, so confirm them with your molder in a design for manufacturing (DFM) review.
Wall Thickness
Start with wall thickness. It controls how the part fills, cools and holds its shape, and most other features are sized from it.
Keep Wall Thickness Uniform
Choose a nominal wall and keep as much of the part as possible close to it. Plastic shrinks as it cools, and thick sections cool more slowly than the walls around them. Uneven cooling causes several common defects.
Sink marks
A thick area keeps shrinking after its surface sets and pulls the surface inward, often opposite a rib, boss or local thickening. Glossy faces show it most.
Warp
Areas that shrink by different amounts make the part bend or twist after ejection. Uneven walls, uneven cooling and the flow direction of the resin all contribute.
Voids and longer cycles
Very thick sections can trap internal voids and take longer to cool, which adds cost to every part.
- Make changes in thickness gradual rather than stepped.
- Core out thick solid areas.
- Round inside corners, with a concentric outside radius, so the wall stays even.
- Take the working thickness range from the resin data and your molder's advice.

Draft
Even walls let the part fill and cool consistently. Draft then decides whether it leaves the mold cleanly.
Add Draft in the Direction the Mold Opens
Draft is a slight taper on faces parallel to the direction the mold opens. Without it, the part drags against the cavity or grips the core during ejection, which can leave scuff marks or distort the part.
Many molders treat one to two degrees as a starting point for smooth faces, with more on deep features. Agree the figure for each area with your molder rather than applying one number everywhere.
Textured faces
Texture forms fine undercuts across the surface, so textured walls need more draft than smooth ones, and deeper textures need more again. Choose the texture early and confirm its draft before the mold design is fixed.
Inside walls and cores
Plastic shrinks onto the core as it cools, so inside walls often grip harder than outside walls. Check deep pockets and tall ribs in particular.
Faces that must stay straight
If a face must be parallel for fit or sealing, mark it on the drawing. The molder can then propose a solution, such as moving the parting line or adding a side action.

Ribs and Bosses
Ribs and bosses need draft too, and they are where an even wall most often breaks down.
Use Ribs, Bosses and Gussets Instead of Thick Sections
Ribs add stiffness without thickening the wall, bosses carry screws, inserts and pins, and gussets brace both where they meet a wall. Size each against the wall it joins, or it brings back the sink and warp that even walls avoid.
Ribs
Keep ribs thinner than the wall they support. Many designers start at roughly half to two-thirds of that wall and adjust for the resin and the visibility of the opposite face. Several shorter ribs usually fill and eject more easily than one tall rib.
Bosses
Core bosses out so their walls stay close to the nominal wall, and tie them to nearby walls with ribs. State the screw, insert or pin each boss must accept so the hole can be sized for it.
Gussets
Give gussets the same thickness logic as ribs, with draft and a radius at the base, so the support does not create a new thick section.

Undercuts
Ribs and bosses usually follow the opening direction of the mold. Features that do not are undercuts, and they change the tool itself.
Limit Undercuts and Plan the Parting Line
An undercut is any feature that stops the part from coming straight out of the mold, such as a side hole, a snap-fit hook or an internal thread. The mold can release it, but each one adds a mechanism to the tool.

Side actions and lifters
Moving mold components pull clear of the undercut before or during ejection. They add tool design and machining, components to maintain and sometimes cycle time. Ask which features need one and what each adds.
Design alternatives
Some undercuts disappear with a change to the part: an opening that lets the core and cavity meet through the wall, a snap hook formed through a window, or a hole turned into the opening direction.
The parting line
The mold halves meet at the parting line, which leaves a fine line on the part. Its position decides how each face is drafted, where flash could form and which features need side actions, so place it with visible faces and critical dimensions in mind.
Gates and Surfaces
Undercuts and the parting line are fixed with the mold design, and so is the point where plastic enters the cavity.
Plan Gates, Weld Lines and Cosmetic Surfaces
The gate is where molten plastic enters the cavity. Its type and position affect how the part fills and shrinks, where weld lines form and what mark remains once the gate is removed.
Weld lines form where separate flow fronts meet, for example beyond a hole. They can be visible and may be weaker than the surrounding material. Before the gate is placed, map the part's surfaces for the molder:
- Visible faces where no gate mark, weld line or ejector mark is acceptable.
- Areas where these marks can be accepted.
- Features that carry load or seal, where a weld line would be a concern.
- The color, gloss or texture reference for each visible face.
Ejector pin positions belong in the same review. The first trial samples show whether these choices worked, so make them part of what each trial must show.

Resin and Shrinkage
Filling and surface quality also depend on how the chosen resin flows and shrinks, so the material decision belongs in the design stage.
Choose the Resin Early and Allow for Shrinkage
Treat the resin as part of the design. Wall thickness, draft, rib proportions and gate position all depend on how the chosen grade flows, cools and shrinks.
The mold cavity is made oversize to allow for shrinkage, based on the grade's shrinkage data and the molder's experience with similar parts. Changing the resin after the mold is made can therefore move dimensions, not only material properties.
Resin type
Semi-crystalline resins, such as polypropylene and acetal, generally shrink more than amorphous resins, such as ABS and polycarbonate.
Fillers and reinforcement
Glass and mineral fillers change stiffness and shrinkage. Fiber-filled grades often shrink differently along and across the flow, which can affect flatness.
Color and additives
Colorants, flame retardants and other additives can change how a grade molds. State any required grade, color or rating, and whether alternatives may be proposed.
DFM Review
With the resin chosen and the main features drafted, the design is ready for review before tool work begins.
Ask for a DFM Review Before Tooling Starts
A DFM review checks your design against the way the mold will be built and run. Ask for it before the mold design is released, while its findings are still edits to the model.
Send the information the review needs:
- The 3D model and drawing, with a clear revision.
- The intended resin grade and color, and whether alternatives are acceptable.
- Cosmetic faces, critical dimensions and features that must not change.
- First-order quantity and expected repeat demand.
- Any surface texture and your sample milestone.
Expect specific findings: where walls, draft or undercuts may cause problems, a proposed gate, parting line and ejector layout, and any recommended changes. Record each change you accept in a new revision, so the mold is built from an agreed design.
Bohui produces injection molded parts in its own factory. Read about the injection molding service, or send your design and these details with your quote request.
Discuss the Requirement with Bohui
Share the part information and the decision you need to make.
Jane
BOHUI PROTOTYPES LIMITED
I'm Jane, the contact for your enquiry.
You can also reach me by email or on WhatsApp.
Jane
BOHUI PROTOTYPES LIMITED
- Address: Xiaobian Street, Chang'an Town, Dongguan City, Guangdong Province, China
Request a Quote
Fields marked are required.


