Skip to content
Request a Quote
Menu
Placeholder for a photo (BH-A10-S01-I01)

Mold Trials, T1 Samples and Mold Approval

Before a new mold goes into production, agree three things with your molder: what each trial must show, how the samples will be reviewed, and how corrections and the final approval will be recorded.

Without that agreement, a trial produces parts but not a decision. Trial samples are the first parts from the actual mold, in the actual resin, made while the molding process is still being set. They show whether the tool fills the part, whether the dimensions and appearance meet the drawing, and what still needs to change. The steps below are a general framework. The details for your project depend on the part, the tool and what you agree with your supplier.

Trial Stages

Start with what a trial means in your order, because suppliers do not all use the same labels.

What a Mold Trial Is

A mold trial is a run of the new mold on a molding machine to produce sample parts and develop the process. It checks that the tool opens, fills, cools and ejects as designed, and it produces the samples you review against the drawing.

Trial labels are not standardized. Some suppliers call the first shots T0 and the first samples sent to the customer T1; others start counting at T1. Later rounds may be numbered or named, for example as a pre-production sample. Define what each label means in your order, covering three points:

Purpose of the trial

What the round is meant to prove, for example a first fill check, a dimensional sample, a cosmetic sample or the final sample before release.

Samples and records

How many samples are sent, which of them are measured, and which records come with them.

Molding conditions

The resin grade and color, any texture, and whether the samples are molded under the process intended for production.

Sample Review

Once the purpose of each trial is defined, the review of its samples can be planned to match.

What to Review on Trial Samples

Review trial samples against the drawing and the agreed requirements, not against the general impression they give. Split the review so that each part of it has a clear basis.

Molding defects

Short shots, flash, sink marks, voids, burn marks and visible weld lines. These usually point to the tool or the process, and they are the first things to resolve.

Critical dimensions

The features that control fit and function, measured against their datums. Agree the method, how many samples are measured and when, since the dimensions of some resins continue to change after molding as the part cools fully or absorbs moisture.

Appearance

Gate marks, the parting line, ejector marks, texture, gloss and color, checked on the cosmetic faces against an agreed reference and viewing condition.

Fit and function

Assembly with mating parts, snap fits, threads, seals or a defined functional test, using samples in the specified resin.

Keep the sample reference with the results: the trial round, the mold and cavity, the resin and the drawing revision. Results that cannot be traced to a trial round are hard to use in the next one.

Placeholder for a photo (BH-A10-S03-I01)

Corrections

A review usually finds something to change. How those findings are recorded decides whether the next trial resolves them.

Record Issues and Agree Corrections

Turn the review into a written list of issues. Each entry should identify the feature, the requirement it misses, the measured or observed result and the proposed correction. Number the entries so they can be closed one by one in later trials.

Separate the types of change, because each is handled differently:

  • Process adjustments made on the molding machine without changing the tool.
  • Tool corrections that bring the part to the agreed drawing.
  • Design changes that alter the agreed drawing or requirement.

Agree before tooling starts who is responsible for each type of change, how it is approved and how it affects cost and timing. A correction needed to meet the agreed drawing and a new design request are often treated differently, but the terms are for you and your supplier to set in the order, not to assume.

For critical dimensions that may need tuning, ask whether the tool can be made metal-safe, often called steel-safe, so that a correction removes material from the mold rather than adding it. Close an issue only when a later sample shows it resolved.

Placeholder for a diagram (BH-A10-S04-I01)

Approval

When the issue list is closed, the remaining step is to agree what the approval actually covers.

Define What Mold Approval Covers

Approval should be a recorded decision, not an assumption drawn from a delivered sample. State what is being approved and the evidence that supports it.

The approved sample

Samples from the final trial, identified by trial round, mold, cavity and resin, and retained as the physical reference for production.

The inspection report

The measured results for the agreed features against the drawing revision, with any accepted deviation stated in writing.

The process conditions

The molding conditions used to make the approved samples, recorded so that production runs on the same basis. Agree how later changes to them will be handled.

Approval of appearance does not automatically approve dimensions or function. If an approval is limited, for example accepted for appearance while one dimension is still open, record the limit and what will close it.

Placeholder for a photo (BH-A10-S05-I01)

After Approval

Approval closes the trial stage. What you agree next decides how the approved part is produced again.

After Approval: Production Release and Repeat Orders

Mold approval and production release are separate steps. Release the first production order against the approved sample, the drawing revision and the agreed inspection scope.

Production release

Confirm the quantity, resin and color, the records required for the first batch and the delivered condition before production starts.

Repeat orders

Reference the approved sample and drawing revision in each repeat order, and flag any change in resin, color, finish or inspection before the order is placed. A change to an approved part may need a new sample review.

The tooling arrangement

Agree who owns the mold, where it is kept, how maintenance and repair are authorized and charged, and what happens if production moves or ends. Settle these terms when the tool is ordered, not after approval.

Plan Trials

Trials, approval and the tooling arrangement can all be written into your request before the mold is quoted.

Plan Trials in Your RFQ

Include the trial plan in your request for quotation, so it becomes part of the scope that suppliers price and you compare:

  • What each trial round must show, and the label you use for it.
  • The number of samples per round and who measures them.
  • The features to measure, the appearance reference and any functional test.
  • The records required with each round and with the final approval.
  • How issues, corrections and design changes will be recorded and approved.
  • The target milestone for approved samples.

Ask each supplier to state the trial and sample scope in its quotation. Two quotes with different trial scopes are not describing the same work. Bohui produces injection molded parts in its own factory, and you can include the trial plan with your design when you send it.

Discuss the Requirement with Bohui

Share the part information and the decision you need to make.

Placeholder for a contact photo of Jane

Jane

BOHUI PROTOTYPES LIMITED

I'm Jane, the contact for your enquiry.

You can also reach me by email or on WhatsApp.

Jane

BOHUI PROTOTYPES LIMITED

  • Address: Xiaobian Street, Chang'an Town, Dongguan City, Guangdong Province, China

Request a Quote

Fields marked  are required.

Jane BOHUI PROTOTYPES LIMITED Privacy Policy