Skip to content
Request a Quote
Menu
Placeholder for a photo (BH-A03-S01-I01)

How to Define Acceptance for Finished Custom Parts

Define acceptance around the condition in which the parts will be supplied.

Identify the critical characteristics, the reference used to judge them, the point in production when they are checked and the records you need. A machining result, a coated component and a completed assembly may need different checks. The aim is to connect the drawing and purchase requirement to the part you will actually receive. Start with dimensions, appearance, material identity and assembly or functional needs. Then decide which of those characteristics need documented evidence.

Condition

The first decision is the delivery condition, because later operations can change what needs to be checked.

Name the Condition in Which Acceptance Applies

State whether the requirement applies to the basic manufactured part, a part after finishing, or another agreed delivery condition.

For sheet metal, distinguish the flat pattern from the formed component. For a coated part, identify dimensions or surfaces that must satisfy the requirement after the coating is applied. For a printed or cast part, identify the relevant post-processing and final material condition.

Where different checks occur at different stages, make the distinction visible. Use intermediate measurements for process control, while retaining the final check you need for assembly.

Placeholder for a diagram (BH-A03-S02-I01)

Fit and Function

Once the stage is clear, the drawing can show which dimensions and interfaces deserve the most attention.

Identify the Features That Control Fit and Function

Not every dimension has the same effect on your product. Identify the mating diameters, hole patterns, locating surfaces, clearances, sealing areas or other features that determine whether the component can be used.

Provide the drawing reference and tolerance for each critical characteristic. Where the measurement depends on how the part is supported or referenced, make that expectation clear in the technical discussion.

For formed or flexible parts, the measurement setup can matter. Agree how the relevant references and assembly condition are represented rather than assuming any measurement of the same nominal dimension is equivalent.

The equipment used for manufacturing does not replace this requirement. A machine positioning specification and a completed-part acceptance tolerance describe different things.

Placeholder for a diagram (BH-A03-S03-I01)

Appearance

Dimensions address geometry. Visible surfaces need their own reference so appearance is not left to a general word such as “good”.

Give Appearance Requirements a Usable Reference

Identify which surfaces are visible in the final application and which areas are hidden or functional. State the requested color, texture, gloss or transparency where relevant.

Use a reference sample or a defined visual standard when an image viewed under unknown conditions cannot establish your acceptance requirement. If a reference image is used, explain what it illustrates and which aspects require further agreement.

Surface marks, color differences and finishing transitions should be discussed for the actual part and process. Avoid treating every surface as equally cosmetic unless that is truly the requirement.

Placeholder for a diagram (BH-A03-S04-I01)

Assembly Checks

A part can meet dimensional and appearance checks while still requiring a separate assembly or functional evaluation.

Separate Assembly Checks from Functional Testing

An assembly check asks whether the part fits with the intended mating components under the agreed condition. A functional test asks whether it performs a defined task.

If an assembly check is required, identify the mating parts or references and the result that should be observed. If a functional test is required, describe the load, temperature, movement, environment or other conditions relevant to the test.

Clarify who performs each check and what result is needed. A supplied component may be only one part of a larger system, so the component inspection and final product validation should not be silently treated as the same responsibility.

Placeholder for a diagram (BH-A03-S05-I01)

Records

The inspection records should reflect those agreed checks rather than add a long list of documents with unclear relevance.

Request Records That Match the Requirement

Decide which characteristics need a recorded result and which documents are needed for the order. Examples may include material information, a first article report, dimensional results or a specifically agreed test record.

State whether the requirement applies to initial samples, selected features, a defined sampling plan or another scope. If you need a particular report format, include it before the quotation is finalized.

A report should be connected to the part reference, drawing revision and relevant check. A generic equipment list or an unrelated sample report does not establish the result for your order.

Bohui's quality control information describes the inspection equipment and documentation categories presented in its company materials. Project-specific checks and records should be identified in the enquiry.

Acceptance Brief

A short acceptance brief can bring these decisions into the quotation before production begins.

Add an Acceptance Brief to Your RFQ

Include:

  • The drawing revision and required delivery condition.
  • The dimensions and interfaces that determine acceptance.
  • The visual surfaces and agreed appearance reference.
  • Any required assembly or functional checks.
  • Who performs the checks and when they take place.
  • The required records and reporting scope.
  • How sample approval relates to later production.

These points help suppliers quote the same requirement and give the buyer a clearer basis for reviewing the delivered parts.

Send a Project Enquiry to Bohui · Prepare a Complete RFQ

Further reading:

Discuss the Requirement with Bohui

Share the part information and the decision you need to make.

Placeholder for a contact photo of Jane

Jane

BOHUI PROTOTYPES LIMITED

I'm Jane, the contact for your enquiry.

You can also reach me by email or on WhatsApp.

Jane

BOHUI PROTOTYPES LIMITED

  • Address: Xiaobian Street, Chang'an Town, Dongguan City, Guangdong Province, China

Request a Quote

Fields marked  are required.

Jane BOHUI PROTOTYPES LIMITED Privacy Policy