Skip to content
Request a Quote
Menu
Placeholder for a photo (BH-A11-S01-I01)

What to Put on a Drawing for Custom Parts

A drawing for a custom part should answer three questions without a follow-up email: which part and revision it is, what shape and size the part must have, and how each requirement will be checked.

The 3D model carries the geometry. The drawing carries what the model cannot show, such as tolerances, datums, material, finish and inspection notes. A gap on the drawing does not stay empty. The supplier fills it with an assumption, a question that delays the quote, or a disagreement when the parts are inspected. The sections below follow the drawing from the title block to the notes, using common practice for machined, fabricated and molded parts.

Title Block

Start with the block that identifies the drawing, because every other requirement is tied to it.

Title Block, Part Number and Revision

The title block identifies the part and sets the rules for reading the rest of the sheet. The supplier quotes, makes and inspects against what it says, so fill in every field that applies instead of leaving template defaults in place.

FieldWhat it tells the supplier
Part number and nameWhich part this is, across the quote, the order and the delivery labels
Revision and dateWhich version is current, and whether it matches the model
Units and scaleWhether dimensions are in millimeters or inches, and the scale of the views
Projection methodWhether the views follow first-angle or third-angle projection
Standards and general toleranceWhich drawing standard applies, and the tolerance for dimensions without their own

Change the revision every time a requirement changes, and record what changed in a revision table. When the drawing and the model carry different revisions, the supplier cannot tell which one to follow.

Views and Datums

With the drawing identified, the views have to show every feature clearly and relate it to the faces the part is measured from.

Views and Datums

Show enough views to define every feature without guesswork, and no more. Most parts need two or three orthographic views. A view that adds nothing new only gives the reader another place to find a conflict.

Datums are the reference features from which other features are located and measured. Pick them from the way the part sits in its assembly, such as a mounting face, a locating bore or a pair of locating holes, and label them on the drawing. The supplier can then hold and inspect the part from the same references you designed it from.

Section views

Cut through the part to show internal features, wall thicknesses and blind holes that hidden lines would only suggest.

Detail views

Enlarge small features, such as grooves, undercuts or thread reliefs, so their dimensions stay readable.

Datum features

Label each datum feature with a letter, and use the same scheme for dimensions, geometric tolerances and inspection.

Placeholder for a diagram (BH-A11-S03-I01)

Critical Dimensions

The views show where each feature is. The dimensions say how large it is and which features control the part.

Dimensions, and Which Ones Are Critical

Dimension each feature once, from the datums where the relationship matters. A dimension shown in two places can disagree with itself after a revision, and a long chain of dimensions passes every tolerance in the chain on to the last feature.

Mark the dimensions that control function. Many companies use a symbol, a balloon or a note to flag critical features, so they are reviewed in the quote and recorded at inspection. Keep that list short enough that it still points to the features that matter.

  • Dimension related features from the same datum instead of from each other.
  • Mark dimensions given only for information as reference dimensions.
  • Give the size and position of every hole, slot and thread, including depth.
  • State whether undimensioned geometry is to be taken from the 3D model.
  • Explain the symbol used for critical dimensions in a note or legend.
Placeholder for a diagram (BH-A11-S04-I01)

Tolerances

Each of those dimensions needs a permitted variation, either its own or one the drawing applies by default.

General and Specific Tolerances

A general tolerance covers every dimension that has no tolerance of its own. State it in the title block or a drawing note, either as a standard and class, such as a class within ISO 2768, or as your company's own table. Without one, the supplier has to decide how close every untoleranced dimension must be.

Specific tolerances belong on the features in your critical list. Put a plus-or-minus or limit tolerance on a size, and use geometric tolerances tied to the datums when position, flatness or profile matters more than a single size.

Match the tolerance to the function

Tight values add machining and inspection time. Use them where a fit, seal or alignment needs them.

Say when a tolerance applies

State whether dimensions apply before or after plating, coating or anodizing, since most finishes change surface dimensions.

Name the GD&T standard

State whether geometric tolerances follow ASME Y14.5 or the ISO GPS series, so each symbol is read under the same rules you used.

Material and Notes

Tolerances define the size. Material, finish and notes define what the part is made of and the condition it is delivered in.

Material, Finish and General Notes

Name the material by its exact grade and condition, not only by family. Aluminum or stainless steel covers many alloys with different strength, corrosion resistance and machinability. If an equivalent grade from another standard is acceptable, say so and name the property it must preserve.

General notes collect the requirements that apply to the whole part. Keep them numbered, short and specific, so each one can be checked.

Finish

Name the finish, its color or reference sample, the faces it applies to and any areas to mask, such as threads, contact faces or grounding points.

Surface texture

Give a roughness value only on faces where it affects function or appearance, and say whether it applies before or after finishing.

Edges and burrs

A note such as "break all sharp edges" covers most edges. Call out a specific chamfer or radius only where an edge has a job.

Placeholder for a photo (BH-A11-S06-I01)

Common Omissions

Most delays come from a short list of items missing from otherwise complete drawings.

Common Omissions on Custom-Part Drawings

The same gaps appear on many drawings sent out for quotation. Each one is quick to fix before the drawing is sent and slow to settle once the parts exist.

  • A revision on the drawing that does not match the model file.
  • No units, or units that differ between the drawing and the model.
  • No general tolerance for dimensions without their own.
  • Thread callouts without pitch, class or depth.
  • A material family with no grade or condition.
  • A finish with no masking areas and no statement on whether dimensions apply before or after it.
  • Critical features that are not marked, or datums that are not labeled.
  • Requirements written only in an email instead of on the drawing.

Before you send the drawing, read it once as the supplier would, with no knowledge of the assembly, and check that each requirement can be made and measured from the sheet alone.

Send Both Files

A drawing that passes that check is ready to travel with the model as one package.

Send the Drawing and Model Together

Send the 3D model and the 2D drawing at the same revision. The model gives the supplier geometry for programming, tooling or a flat pattern, and the drawing gives the tolerances, datums and notes that decide whether the part passes. State which document governs if they disagree, so a conflict is raised as a question instead of settled by assumption. A neutral 3D format such as STEP opens in most CAD systems; check which formats your supplier accepts.

CNC machining, sheet metal fabrication, injection molding, 3D printing and vacuum casting are the five services Bohui produces in its own factory. Whichever route your part takes, send the drawing package with:

  • The 3D model and the 2D drawing, both at the current revision.
  • The quantity for this order and any later quantities you expect.
  • The critical features, and how you need them measured and recorded.
  • Any specifications, standards or appearance references the drawing names.
  • Features you are willing to change if the review suggests it.

Discuss the Requirement with Bohui

Share the part information and the decision you need to make.

Placeholder for a contact photo of Jane

Jane

BOHUI PROTOTYPES LIMITED

I'm Jane, the contact for your enquiry.

You can also reach me by email or on WhatsApp.

Jane

BOHUI PROTOTYPES LIMITED

  • Address: Xiaobian Street, Chang'an Town, Dongguan City, Guangdong Province, China

Request a Quote

Fields marked  are required.

Jane BOHUI PROTOTYPES LIMITED Privacy Policy