How to Specify Tolerances Without Overpaying
Put tight tolerances only where the part's function needs them.
Cover every other dimension with one general tolerance, and say how each critical feature will be checked. Each tight tolerance asks more of the supplier: a slower operation, an extra setup, a longer inspection or a higher chance of rejecting a part. Spent on a feature that does not need it, that effort adds cost and time without improving the product. Sort the features by function first, then write the general tolerance, and confirm with the supplier what the process and material can hold before you fix the numbers.
Feature Function
Sorting starts with one question for every feature on the drawing: what does it have to do?
Start from What Each Feature Has to Do
Decide what a feature is for before you write a number. The tolerance should come from the job the feature does in the assembly, not from a habit of tightening every dimension.
Bores, shafts, pins and locating holes that mate with another part. The tolerance follows from the clearance or interference the joint needs, together with the tolerance of the mating part.
Faces and grooves that hold a gasket or O-ring. Flatness, surface texture and groove size usually decide whether the seal works, more than the overall size of the part.
Hole patterns and faces that position other components. The relationship between features often matters more than any single size.
Visible edges, gaps and surfaces. These are often better controlled with an appearance reference and a clear note than with a tight dimension.
A feature that does none of these jobs, such as an outside face with clearance all around it, can usually take the general tolerance. Mark the features that do, so the supplier can see where the effort belongs.

General Tolerances
With the critical features marked, the rest of the drawing can follow one clear rule instead of a separate number on every dimension.
Use a General Tolerance for Everything Else
A general tolerance applies to every dimension that has no tolerance of its own. It is normally stated in the title block or as a drawing note, so you do not have to tolerance each size individually.
Reference a general tolerance standard, such as ISO 2768, and name the class you are applying within it. The standard's name alone does not tell the supplier which level of control you intend. If your company uses its own tolerance table, send it with the drawing.
| Dimension type | How to specify it | What the supplier needs to see |
|---|---|---|
| General dimensions | One general tolerance note in the title block | The standard or table, and the class selected |
| Critical dimensions | An individual tolerance on the feature | Why the feature is critical and how it will be checked |
| Feature relationships | A geometric tolerance tied to datums | The datum features and the drawing standard followed |
| Reference dimensions | Marked as reference, with no tolerance | Agreement that they are for information only |
| Cosmetic features | A note or appearance reference | The visible faces and the agreed reference |
Keep the critical list short. When every dimension carries a tight tolerance, the supplier cannot tell which features control the part.
Cost and Time
Each tolerance tighter than the general rule changes how the part is made and checked, and that is where the extra cost comes from.
Why Tight Tolerances Add Cost and Time
A tighter tolerance rarely changes the price of the material. It changes the work around it, and the effect builds up in four places.
A close size or a fine surface can need lighter finishing cuts, a different tool or a secondary operation such as reaming or grinding. Each one adds machine time.
When related features must be held tightly to each other, they may need to be cut in one setup or located in a dedicated fixture. Moving the part between setups can use up much of a tight tolerance on its own.
Every critical feature has to be measured with a method that can resolve its limits. Tighter limits can call for a more capable instrument, a controlled measuring environment or more parts checked.
The closer the limit, the more parts can fall outside it. Scrap, rework and the extra parts started to cover them are part of the quoted price, even when they are not listed.
None of this is a reason to loosen a tolerance the function needs. It is a reason to check each tight value against your list of critical features before the drawing goes out.
Process and Material
How hard a given tolerance is to hold also depends on the process and the material, so the realistic range has to be judged part by part.
The Process and Material Change What Is Realistic
The same tolerance can be routine on one part and difficult on another. Holding a size on a stiff metal block is a different task from holding it on a thin plastic wall, a long slender feature or a part that will be coated after machining.
Factors that change what a supplier can hold include:
- The stiffness, hardness and thermal behavior of the material.
- Internal stress that can move the part as material is removed.
- Part size, wall thickness and the way the part can be held.
- Heat treatment, coating or plating applied after machining.
- The temperature and condition in which the part is measured.
Tolerance tables published in design guides and by suppliers are general starting points. They depend on the material, the feature and the drawing, and none of them describes your part. Ask the supplier to confirm what it can hold on your critical features, in your material and finished condition, before you treat a value as fixed.

Datums and GD&T
Some requirements are about how features relate to each other rather than their size, and that is the job of datums.
Datums and Basic GD&T in Plain Words
A datum is a reference feature, such as a mounting face or a locating hole, from which other features are located and measured. Choose datums that match how the part sits in its assembly, so that the drawing describes the part the way it will be used.
Geometric dimensioning and tolerancing (GD&T) uses symbols to control form, orientation and location relative to those datums. Three callouts appear often on machined parts.
Position
Controls where a hole or other feature sits relative to the datums. It can replace a chain of plus-or-minus dimensions with one clear tolerance zone.
Flatness and perpendicularity
Control the form of a surface and its orientation to a datum. They suit sealing and mounting faces where size alone does not show whether the part works.
Profile
Controls a curved or complex surface against the nominal shape in the model. It is the practical choice when the shape matters and individual dimensions would not describe it.
State which GD&T standard the drawing follows, for example ASME Y14.5 or the ISO GPS series, so the supplier reads each symbol under the same rules you used. Use geometric callouts on the features in your critical list, not on every surface.

Your RFQ
The final step is to send these tolerance decisions with the drawing, in the same form to every supplier you ask.
Bring Tolerance Decisions into the RFQ
Send the tolerance decisions with the drawing, so each supplier quotes the same requirement. Include:
- The drawing revision, units and the general tolerance note in the title block.
- A short list of critical features and the function of each one.
- The datum scheme and the GD&T standard the drawing follows.
- Whether tolerances apply before or after finishing or coating.
- How each critical feature will be checked and which results you need recorded.
- Any tolerance you are willing to review if the supplier proposes a change.
Ask each supplier to flag any tolerance it considers difficult for the chosen process and material, and what it would suggest instead. A question settled before the order is easier to resolve than a disagreement at inspection.
Discuss the Requirement with Bohui
Share the part information and the decision you need to make.
Jane
BOHUI PROTOTYPES LIMITED
I'm Jane, the contact for your enquiry.
You can also reach me by email or on WhatsApp.
Jane
BOHUI PROTOTYPES LIMITED
- Address: Xiaobian Street, Chang'an Town, Dongguan City, Guangdong Province, China
Request a Quote
Fields marked are required.


