Skip to content
Request a Quote
Menu
Placeholder for a photo (BH-A05-S01-I01)

CNC Machining Design Guide

Design CNC parts for tool access, standard tools and stable setups.

Machining time, and with it much of the cost, depends on how easily a round cutting tool can reach each feature and how securely the part can be held. Geometry that a standard tool cannot reach, or that flexes while it is being cut, needs special tools, extra setups or slower machining. Small design changes at those features can shorten the work without changing what the part does. The guidance below gives general starting points. Suitable values depend on the material, the feature and the drawing, so confirm them with your supplier before you finalize the design.

Corners and Cavities

Tool shape shows first in the corners and depth of pockets and cavities.

Internal Corners and Cavity Depth

A milling cutter is round, so every vertical internal corner it cuts keeps a radius at least as large as the tool's radius. A sharp internal corner cannot be milled directly, and a very small radius forces a small tool that cuts slowly.

Give internal corners a radius

Make the corner radius slightly larger than the radius of the tool expected to cut it, so the tool can move through the corner instead of stopping in it. A larger radius allows a larger, stiffer tool.

Keep cavities in proportion

Deep, narrow pockets need long tools that bend and vibrate. A common starting point is a cavity depth of no more than about four times its width, with deeper cavities checked with the supplier.

Relieve corners for square mating parts

If a square-cornered part must sit fully in a pocket, add a small relief cut into each corner, sometimes called a dog-bone, instead of asking for a sharp corner. The mating part then clears without a special tool or process.

Placeholder for a diagram (BH-A05-S02-I01)

Thin Walls

Depth is one side of stiffness. The other is how thin the walls and features around the cavity are.

Walls and Thin Features

Thin walls flex under the cutting force. They can vibrate, lose size or spring back after the cut as internal stress is released, which makes them hard to hold to tolerance and can leave chatter marks on the surface.

Metals and plastics behave differently. Metals are stiffer and usually tolerate thinner walls. Plastics flex more, can soften with cutting heat and may move after machining, so a plastic wall of the same height generally needs to be thicker. Let the material's behavior, not one fixed number, set the minimum.

  • Keep tall walls in proportion to their thickness, since height makes a thin wall harder to cut.
  • Stiffen thin walls with ribs or by joining them to other features where the design allows.
  • Avoid long unsupported fins and tabs unless the function needs them.
  • Tell the supplier which faces of a thin wall are critical, so the machining sequence can protect them.

Holes and Threads

Holes and threads appear on almost every machined part, and standard sizes keep them quick to make.

Holes and Threads

Holes are quickest to produce with standard drills, and threads with standard taps or thread mills. A hole that matches a standard drill size avoids slower milling or boring, unless the fit calls for it.

Use standard sizes

Choose hole diameters that match standard drill sizes where an exact fit is not needed, and standard thread sizes in the unit system of your drawing.

Keep holes reasonably shallow

Deep, narrow holes need long drills and frequent chip clearing. A depth of about four times the diameter is a common starting point, and deeper holes should be confirmed with the supplier.

Limit thread length

Thread engagement beyond about three times the nominal diameter usually adds little holding strength. Extra length adds machining time without making the joint stronger.

Leave room below blind threads

In a blind hole, allow drilled depth below the last full thread so the tap or thread mill has space to finish. Call out the full-thread depth you need.

Show each thread with a complete callout on the drawing, including size, pitch, class or fit where relevant, and depth. A thread modeled in the CAD file is not always read the same way by every supplier.

Placeholder for a diagram (BH-A05-S04-I01)

Setups and Datums

Every feature also has to be reached from some direction, and the number of directions decides how often the part is clamped again.

Setups, Datums and When Multi-Axis Machining Helps

Each time a part is turned over and clamped again, it has to be located again, and small differences between setups can add up. Features that must relate closely to each other are easier to hold when they can be cut in the same setup.

Design with workholding in mind. Give the part flat, accessible faces for clamping, and choose datums that the supplier can also use to locate the part. If a surface must not carry clamp marks, say so on the drawing.

Three-Axis Machining

Suits parts whose features can be reached from a small number of directions. Grouping features on faces that share a direction reduces the number of setups.

Multi-Axis Machining

Four- and five-axis machining can reach angled features and several faces with fewer re-clamps. It helps when critical relationships span several faces or the surface is complex, but the part still needs a stable way to be held.

Placeholder for a photo (BH-A05-S05-I01)

Edges and Finishes

Once the main features are cut, edges, text and surface requirements decide how much finishing work remains.

Edges, Text and Surface Finish Callouts

Machining leaves sharp edges and small burrs. A general note such as “break all sharp edges” covers most of them. Call out a specific chamfer or radius only where an edge has a job, such as a lead-in for assembly or a surface the user will handle.

Edges

An external chamfer is usually quicker to machine than an external radius, which needs a form tool or a three-dimensional toolpath. Specify a radius where the shape matters.

Text and logos

Engraved text is generally simpler than raised text, which requires removing material around every character. Keep characters large enough for a small tool and use a simple font.

Surface finish

An as-machined surface shows tool marks. Specify surface roughness only on faces where it affects function or appearance, and say whether the value applies before or after any coating.

Material Choice

Each of these guidelines shifts with the material, which affects how quickly and cleanly every feature can be cut.

Material Affects Machinability

The same geometry can take very different machining time in different materials. Free-machining aluminum alloys and brass usually cut quickly. Stainless steel, titanium and other hard or tough alloys cut more slowly and wear tools faster. Plastics cut easily but can melt, deflect or move after machining.

Choose the material for the part's function first, then ask whether a more machinable grade in the same family would meet the requirement. If a specification fixes the material, keep it fixed and adjust the design instead.

  • Name the exact grade and condition, not only the material family.
  • Say whether a substitute is acceptable and which properties it must preserve.
  • Note any heat treatment or hardening before or after machining.
  • For plastics, identify features that must stay flat or stable after machining.
Placeholder for a photo (BH-A05-S07-I01)

Design Review

With these points built into the design, a short review with the supplier can settle the remaining choices before the quote is final.

Send the Design for a Manufacturability Review

A short design review before the quote is final can catch a feature that would need a special tool, an extra setup or a tighter tolerance than the function requires. The supplier can propose a change, and you decide whether the function allows it.

CNC machining is one of the five services Bohui produces in its own factory. To review your part, send the model and drawing together and identify:

  • The current revision of the 3D model and the 2D drawing.
  • The material grade, quantity and required finish.
  • The critical features, datums and their tolerances.
  • Features you are willing to change, such as corner radii, depths or thread lengths.
  • Surfaces that must not carry clamp or tool marks.

Discuss the Requirement with Bohui

Share the part information and the decision you need to make.

Placeholder for a contact photo of Jane

Jane

BOHUI PROTOTYPES LIMITED

I'm Jane, the contact for your enquiry.

You can also reach me by email or on WhatsApp.

Jane

BOHUI PROTOTYPES LIMITED

  • Address: Xiaobian Street, Chang'an Town, Dongguan City, Guangdong Province, China

Request a Quote

Fields marked  are required.

Jane BOHUI PROTOTYPES LIMITED Privacy Policy