3D Printing Design Guide
Design the part for the printing process you will use.
FDM, SLA, SLS and MJF build parts in different ways, so each has its own limits on walls, overhangs, holes and surface. A design that prints cleanly in one process can warp, fail or need heavy finishing in another. Choose the process first, from what the part has to do. Then apply that process's rules to the walls, the build orientation, the holes and fits, and the finish. The guidance below gives general starting points. Suitable values depend on the process, the material and the size of the part, so confirm them with your supplier before you finalize the design.
Choose the Process
The process decides most of the other rules, so it is the first choice to make.
Choose the Process First
Each process suits different jobs. Start from what the part has to show or survive, such as appearance, fit, a functional load or a small batch, and choose the process whose material and surface suit that job.
| Process | How it builds the part | Often chosen for | Design point to watch |
|---|---|---|---|
| FDM | Extrudes melted plastic filament through a nozzle | Concept models, fixtures and larger simple parts | Visible layer lines and lower strength between layers |
| SLA | Cures liquid resin with light, layer by layer | Fine detail and smooth surfaces for visual models | Needs supports; resin properties differ from production plastics |
| SLS | Fuses plastic powder, commonly nylon, with a laser | Functional parts and complex shapes without supports | Grainy surface; powder must escape from enclosed cavities |
| MJF | Fuses plastic powder, commonly nylon, with an agent and heat | Functional parts and small batches | Grainy surface, often gray or dyed |
Material names vary between suppliers, and a resin described as similar to a production plastic is not that plastic. Confirm the exact material and its data for any property you plan to test.
Walls and Details
Once the process is known, its smallest reliable feature sets the limit for walls and fine details.
Walls and Small Features
The thinnest wall a process can build reliably depends on the nozzle, the laser spot or the powder, and on the material. A thin wall may print, then warp, break during support removal or bend during powder cleaning. Tall or large thin walls are more at risk than short ones.
Ask the supplier for the minimum wall and feature sizes for the process and material you chose, and design above them where the function allows.
Thin pins break easily, and in FDM a vertical pin can snap between layers. Thicken them or add a fillet at the base.
Embossed and engraved text needs enough stroke width and depth to stay readable. Keep characters bold and simple.
Narrow gaps can fuse shut in powder processes, and narrow channels can trap resin or powder that cannot be cleared.
A hollow part in SLA, SLS or MJF needs escape holes to remove trapped resin or powder. At least two holes are a common starting point, so material can flow out while air flows in.

Orientation
Whether a feature prints well also depends on which way it faces in the build.
Build Orientation and Supports
The orientation of the part in the build changes its strength, surface and accuracy. Printed parts are usually weakest across the layer lines, most of all in FDM. Curved and sloped faces show a stepped surface, and faces that touch supports carry marks after the supports are removed.
FDM and SLA need supports under overhangs. In FDM, overhangs up to about 45 degrees from vertical are a common starting point for printing without support; steeper faces need support or a design change, such as a chamfer in place of a flat ceiling. In SLS and MJF the surrounding powder supports the part, so no supports are needed, though large flat areas can still warp.
Tell the supplier what the orientation has to protect:
- The direction of the main load, if the part will be tested.
- Cosmetic faces that should not carry support marks.
- Critical dimensions and faces that need the best accuracy.
- Features that must stay round, such as bores and pins.

Holes and Fits
Orientation also affects holes and fits, which often decide whether printed parts assemble.
Holes, Threads and Fits Between Printed Parts
Printed holes often come out slightly undersize or out of round, more so for small holes and for holes built on their side. Where a hole must be accurate, print it slightly undersize and drill or ream it to size afterwards, and mark which holes need that step.
Threads
Small printed threads are rough and weak. For threads that are tightened repeatedly, use threaded inserts, such as heat-set inserts, or tap the hole after printing. Larger threads can be printed when the fit is not critical.
Fits between printed parts
Printed parts need more clearance between them than machined parts. The amount depends on the process, the orientation and the size of the faces, so ask the supplier for a starting value and test it on a sample.
Snap-fits and hinges
Flexible features depend on the material. Nylon from SLS or MJF usually takes repeated flexing better than many SLA resins, which can be brittle.

Finishing
Most printed parts are finished in some way after printing, and finishing changes surfaces and sizes again.
Post-Processing and Surface
Every process leaves its own surface. FDM shows layer lines, SLA is smooth with small marks where supports touched, and SLS and MJF parts have a fine grainy texture. Post-processing improves the surface but adds time, and many steps remove or add material.
Common steps include support removal, sanding, bead blasting, dyeing, priming and painting, and clear coating for see-through parts. Which steps suit your part depends on the process and the material.
- Mark the faces that are cosmetic and the faces that can stay as printed.
- Give a color, gloss or texture reference for finished faces.
- State which dimensions must hold after finishing.
- Note whether inserts go in before or after painting.

Switching Process
If a part needs heavy finishing, a production material or close fits on every piece, another process may suit it better.
When to Switch to Another Process
3D printing suits early design rounds, complex shapes and small quantities. As a design settles, those reasons can fall away. Consider another process when the part needs a production material, close fits on every piece, a surface that takes heavy finishing on each part, or a quantity at which a tooled process costs less per part.
CNC machining
Makes parts from production metals and plastics with close tolerances, when a cutting tool can reach the shape.
Vacuum casting
Copies a master into small batches of cast polyurethane parts. A printed part can often serve as the master.
Injection molding
Suits larger quantities in production plastics. The design usually needs draft and even walls that the printed part did not require.
Send the Model
Whichever route comes next, a quote for a printed part starts from the model file and what the part has to do.
Send the Model with the Part's Job
3D printing is one of the five services Bohui produces in its own factory. A printing quote depends on the process, material, orientation and finishing, so send the model together with what the part has to do. If you have not fixed a process, the supplier can then suggest one.
Mesh files such as STL carry no units and approximate curved faces with flat triangles. Export at a resolution fine enough for your curved surfaces, and state the units. A neutral CAD format such as STEP keeps exact geometry for features you need to dimension; check which formats your supplier accepts.
- The model file, its units and its revision.
- The process and material, or the job the part has to do.
- The quantity, and whether more rounds are expected.
- Critical dimensions and how they will be checked, with a drawing if tolerances matter.
- Cosmetic faces, finish and any inserts or assembly.
Discuss the Requirement with Bohui
Share the part information and the decision you need to make.
Jane
BOHUI PROTOTYPES LIMITED
I'm Jane, the contact for your enquiry.
You can also reach me by email or on WhatsApp.
Jane
BOHUI PROTOTYPES LIMITED
- Address: Xiaobian Street, Chang'an Town, Dongguan City, Guangdong Province, China
Request a Quote
Fields marked are required.


