Sheet Metal Design Guide
Design a sheet metal part around the sheet it starts as.
The part is cut from one flat blank of one thickness, then bent, joined and finished. A design that keeps a single thickness, uses bends the tooling can form and keeps features clear of those bends is quicker to make and more consistent from part to part. Cost and variation grow with the number of operations. Every extra bend, weld, hardware insert or masking step adds handling. The guidance below gives general starting points. Suitable values depend on the material, the thickness and the supplier's tooling, so confirm them with your supplier before you finalize the design.
Material and Thickness
The first decisions are the material and its thickness, since the rules for every bend and feature are set relative to them.
Choose the Material and Thickness Together
Choose the material for what the part has to do: carry a load, resist corrosion, save weight, conduct current or take a particular finish. Then check that the grade can be formed into the shape you need.
Keep one commonly stocked thickness for the whole part. Give it in millimeters or inches rather than as a gauge number, because one gauge number stands for different thicknesses in different materials.
| Material family | Often chosen for | Design point to check |
|---|---|---|
| Cold-rolled steel | Brackets, frames and painted enclosures | Needs a coating or plating to resist corrosion |
| Stainless steel | Corrosion resistance and a bare finished look | Springs back more after bending and is harder to form |
| Aluminum | Light parts and enclosures, often anodized | Harder tempers can crack at tight bends |
| Pre-coated or galvanized steel | Corrosion protection applied before fabrication | Cut edges and welds lose the original coating |
| Copper and brass | Electrical conductivity and appearance | Soft surfaces mark easily |
The grades and thicknesses on offer vary by supplier, so confirm the exact sheet before you fix the design.
Bend Radii
With the sheet chosen, the bend radius is the first dimension that has to follow from it.
Bends and Bend Radii Relative to Thickness
A press brake forms each bend between a punch and a die, and the inside radius depends on that tooling, the material and the thickness. A common starting point is an inside bend radius about equal to the sheet thickness. Harder alloys and tempers often need a larger radius, and some soft materials can take a smaller one.
The sheet springs back slightly after each bend, so give bend angles that do not affect fit a looser tolerance.
Give every bend on the part the same inside radius where the design allows. Each additional radius can mean another tool change.
The die needs enough flange to hold the sheet during the bend. A flange length of at least about four times the thickness is a common starting point.
Where a bend ends at an edge or meets another bend, a small relief cut stops the material tearing or bulging at the corner.
Short flanges between bends, deep U-channels and closed boxes can hit the tooling, so ask the supplier to check the bend sequence.

Features Near Bends
Bending stretches the material near the bend line, and that affects any hole or slot placed close to it.
Holes, Slots and Features Near Bends
Material near a bend line stretches on the outside and compresses on the inside as it forms. A hole or slot too close to the bend can distort into an oval or move out of position. A common starting point is to keep the edge of a hole at least about two and a half times the thickness, plus the inside bend radius, away from the bend.
If a feature has to sit closer, it can be cut after bending, which adds an operation, or a relief slot can run through the bend line.
- Make holes at least as large in diameter as the sheet thickness, as a common starting point.
- Leave material between holes, and between a hole and the edge, so the web does not tear or bulge.
- Allow more distance for formed features such as louvers, embosses, countersinks and extruded holes.
- Size holes for inserted hardware from the hardware maker's data, not from a general rule.

Flat Pattern
Many requirements also link faces that are separated by one or more bends.
The Flat Pattern and Tolerance Build-Up Across Bends
Every formed part starts as a flat blank, and its length depends on how the material stretches in each bend. That varies with the material, the thickness and the supplier's tooling, so the supplier usually generates or adjusts the flat pattern from your formed 3D model. If you send your own, say whether it may be adjusted.
Features cut in the same flat face are positioned in one cutting operation. Features related across a bend also carry the variation of the bend angle and bend position, and that variation grows with each bend between them.
Dimension from the face that matters
Measure critical features from the flange they locate against, not across several bends, and keep features that must align on the same face where you can.
Allow for build-up across bends
Give dimensions that span several bends a tolerance that reflects the bends between them, and confirm a realistic value with the supplier.
Absorb variation in the assembly
Slots, larger clearance holes or floating hardware let mating parts line up when formed sizes vary within tolerance.

Joining
Many sheet metal parts end up as assemblies, and each joining method brings its own rules.
Joining: Welding, Hardware and Fasteners
Choose the joining method early, because it affects the flat pattern, the hole sizes and the finishing sequence. Show on the drawing which joints are required, and leave the method open where any secure joint will do.
Welding
Welding heat can distort thin sheet. Give the welder access to the joint, specify weld size and length only where strength needs it, and say whether visible welds must be ground flush.
Inserted hardware
Self-clinching nuts, studs and standoffs are pressed into holes in the sheet. Follow the hardware maker's data for minimum sheet thickness, hole size and distance from the edge.
Screws and rivets
Leave tool access on both sides of the joint, and size clearance holes for the alignment the assembly needs.
Name each piece of hardware by type, size and material, and say who sources it. Confirm whether hardware goes in before or after finishing, since a coating can reach threads and press-fit holes.

Finishes
The finish comes last, but it has to be planned with the joints and hardware it covers.
Finishes and Protected Surfaces
Pick the finish to suit the material and the use. Steel parts are commonly painted, coated or plated to resist corrosion, aluminum parts are often anodized or painted, and stainless steel is often left bare with a brushed or grained surface.
A coating adds thickness. It can close up tight holes, fill threads and change the fit between mating parts, so design those features with the finish in mind and state whether dimensions apply before or after finishing.
- Mark the cosmetic faces, so forming and handling marks are kept off them.
- Identify threads, contact faces and grounding points that must be masked.
- Give a color and gloss reference for painted or coated parts.
- State the grain direction for brushed surfaces.
- Say whether finished faces need protective film in packing.
Design Review
Each of these choices is easier to settle in a short review before the quote than after the first parts arrive.
Ask for a Design Review Before the Quote Is Final
A short design-for-manufacturing review can catch a bend radius the tooling cannot form, a hole that will distort near a bend, or a tolerance the bends cannot hold. The supplier proposes a change, and you decide whether the function allows it.
Sheet metal fabrication is one of the five services Bohui produces in its own factory. To review your part, send:
- The formed 3D model and the drawing, both at the current revision.
- Your flat pattern, if you have one, and whether it may be adjusted.
- The material grade, condition and thickness.
- Critical dimensions and the faces they are measured from.
- Joining, hardware and finish requirements, including masked areas.
- The quantity, and whether the part will be ordered again.
Discuss the Requirement with Bohui
Share the part information and the decision you need to make.
Jane
BOHUI PROTOTYPES LIMITED
I'm Jane, the contact for your enquiry.
You can also reach me by email or on WhatsApp.
Jane
BOHUI PROTOTYPES LIMITED
- Address: Xiaobian Street, Chang'an Town, Dongguan City, Guangdong Province, China
Request a Quote
Fields marked are required.


