Cosmetic Standards for Visible Parts
A cosmetic standard answers three questions: which surfaces matter, which defects are acceptable on each of them, and how the parts will be judged.
Agree all three with your supplier before production, and "looks good" becomes a requirement that both sides can check in the same way. Without that agreement, acceptance depends on who looks at the part, under which light and for how long. One inspector passes a sink mark that another rejects, and a dispute after delivery comes down to two opinions. The guidance below is a general framework. The right level of detail depends on the part, where it is used and what you agree with your supplier.
Cosmetic Zones
Start on the drawing, because not every surface of a part needs to look perfect.
Mark Cosmetic Surfaces on the Drawing
Mark which faces the end user sees and which are hidden once the product is assembled. Many companies use classes for this, such as class A for the most visible faces, class B for faces seen occasionally and class C for hidden faces. Class names and meanings vary between companies, so define them on the drawing or in a cosmetic specification.
Mark the zones face by face, not for the part as a whole. A housing may have a class A front, class B sides and class C internal ribs. Calling the whole part "cosmetic" adds cost to faces nobody sees and leaves the important face no better defined.
For molded parts, mark the zones before the mold is designed. Gates, ejector pins and the parting line all leave marks, and their positions are set in the mold design.
Class A: primary visible faces
The faces a user sees in normal use, such as the front of a housing or a control panel. They get the tightest limits, and gates, ejector marks and machining steps are kept off them where the design allows.
Class B: secondary faces
Faces seen occasionally or at an angle, such as the sides or underside of a handheld product. Minor marks are often accepted within agreed limits.
Class C: hidden faces
Internal faces and faces covered in assembly. These are usually checked for fit, function and cleanliness rather than appearance.

Defects by Process
With the zones marked, list the defects each zone can and cannot accept. Those defects differ by process.
Common Cosmetic Defects by Process
Each process leaves its own marks, and some cannot be removed completely, only moved, reduced or hidden. Your standard should name the defects that apply to your part and say which zones may show them, and to what extent.
| Process | Typical cosmetic defects | Points to agree |
|---|---|---|
| Injection molding | Sink marks, flow lines, gate marks, weld lines, ejector marks, flash | Gate and ejector positions, texture or gloss, which marks class B faces may show |
| CNC machining | Tool marks, step lines between setups, burrs, clamp marks | Surface finish on visible faces, edge break, whether tool marks may show |
| Sheet metal | Scratches, bend and die marks, weld and grinding marks, dents | Protected or brushed faces, which side the bend marks fall on, how visible welds are finished |
| Coated or finished parts | Runs, orange peel, inclusions, thin coverage at edges, color or gloss variation | Color and gloss reference, masking, where rack or hanging contact points may fall |
| Any process | Handling scratches, dents, fingerprints, residue | Cleaning, handling and packing before and after finishing |
Cosmetic specifications often limit a defect by its size, the number allowed on one face and the distance between them, with different limits for each class. Agree the defect list and limits for the actual part, material and finish with your supplier.
Inspection Conditions
A defect list still needs a shared way of looking for those defects.
Agree the Inspection Conditions
Whether a defect is visible depends on how closely, in what light and for how long someone looks. Agree them in writing, so the supplier's outgoing check and your incoming check judge parts the same way.
Set the conditions to match how the product is seen in use. A face viewed from across a room does not need to be judged as if it were held close to the eye under a bright lamp.
A fixed distance between the eye and the surface, usually close to the distance at which a user would normally see the part.
The type and brightness of the light, and whether it is diffuse or angled. Light at a low angle reveals far more than everyday lighting, so agree whether it is part of the check.
How long each face is examined and from which angles. A short, set time per face judges what a user would notice, not what a close search can find. Cosmetic checks are commonly made without magnification.
When the parts are checked, for example after finishing and before packing, and how that relates to the check on arrival.
Agree values for the distance, lighting and viewing time with your supplier, and write them into the specification.

Reference Samples
Written limits are easier to apply when a physical part shows where they fall.
Use Reference Samples and Limit Samples
Words and numbers describe a defect; a sample shows it. For color, gloss, texture and marks that are hard to measure, a physical sample agreed by both sides is usually the clearest basis for acceptance.
Reference sample
An approved part that shows the intended appearance, such as the color, gloss and texture of a class A face. It is often chosen from approved samples or the first accepted batch and labelled as the reference.
Limit samples
Parts that show the worst condition still acceptable for a given defect, such as the largest sink mark or the lightest color shade accepted. Some buyers also keep an example just outside the limit. Limit samples make borderline decisions quicker and more consistent.
Keeping and renewing samples
Label each sample with the part number, drawing revision, what it shows and who approved it. Keep a matching set at both ends, away from light and handling, and agree when it is replaced, since some materials and finishes change over time.
A photograph can explain the intent, but screens and lighting change what it shows, so it cannot replace a physical sample for a close match.

Surface Protection
A part that passes inspection can still be marked before it reaches you, so protection belongs in the standard too.
Protect Finished Surfaces in Handling and Packing
Many cosmetic rejects are caused after the part is made: between operations, during finishing, in packing or in transit. A cosmetic standard only holds if the surface stays intact until the parts are inspected on arrival.
Agree the protection at each stage, to suit the part and the finish:
- Gloves and clean handling for finished and coated faces.
- Protective film on polished, brushed or clear class A faces, removed at assembly.
- Masking or covers on faces that must stay clean during later operations.
- Separators, trays or individual bags so parts do not touch each other.
- Soft wrap or foam, not hard edges, in contact with visible faces.
- Labels with the part number and revision, so boxes need not be opened twice.
Some protective films leave residue if left on too long or exposed to heat, so check the film suits the finish. Inspect visible faces on arrival, before stocking, while any transit damage can still be traced.

Cosmetic RFQ
Zones, defects, inspection conditions, samples and protection can all be stated in your request before the parts are quoted.
Add the Cosmetic Requirement to Your RFQ
Cosmetic work adds handling, finishing, masking, packing and inspection time. Put the cosmetic requirement in your request for quotation, so every supplier prices the same standard:
- The drawing or specification that marks class A, B and C faces.
- The defects controlled on each class, and any not allowed at all.
- The viewing distance, lighting and viewing time for inspection.
- The color, gloss or texture reference, and whether limit samples will be made.
- The protection and packing needed for finished faces.
- Where cosmetic inspection takes place and which records you need.
Bohui produces CNC machined, sheet metal, injection molded, 3D printed and vacuum cast parts in its own factory. Send your drawing with the cosmetic zones marked, and say which faces matter most.
Discuss the Requirement with Bohui
Share the part information and the decision you need to make.
Jane
BOHUI PROTOTYPES LIMITED
I'm Jane, the contact for your enquiry.
You can also reach me by email or on WhatsApp.
Jane
BOHUI PROTOTYPES LIMITED
- Address: Xiaobian Street, Chang'an Town, Dongguan City, Guangdong Province, China
Request a Quote
Fields marked are required.


